manualshive.com logo in svg

Solid State Logic AWS DELTA 916, Owner'S Manual, Page: 108 / 239

Share
Download
Solid State Logic AWS DELTA 916 Owner'S Manual Download Page 108

DAW Control

C

OMMUNICATION WITH YOUR

DAW

The AWS connects to your chosen DAW via three MIDI ports at the rear of the console or via MIDI over Ethernet. Each

AWS DAW layer emulates three HUI or MCU controllers. The HUI and Mackie Control (MCU) protocol are widely

supported by DAW manufacturers. 

Section 1 details the MIDI and/or network connections between console and computer and the installation of the

ipMIDI driver software and how to configure Protools. Information relating to other DAW systems is included later in

this section.

Refer  to  your  DAW  manual  for  information  on  how  to  configure  your  software.  Once  configured  and  connected,

communication with the DAW will be initialised, and the level of the AWS channel faders, rotary controls and master

functions will be set to match the DAW controls (provided you are in DAW Focus mode and have the right DAW layer

enabled).
When using your DAW without the AWS, you should remove the AWS from the MIDI controllers section of your DAW

(please see the information specific to your DAW).

Page 4-4

AWS 

δ

elta

Owner’s Manual

Summary of Contents for AWS DELTA 916
















































































































































































































































Reviews:

No comments