Solgaz GNC-4 Assembly And Instruction Manual Download Page 15

15 

 

4.4.8.  Turning the controller lock on and off 

 

The controller lock protects the hob against accidental starting or a change in the 

power of the working burners.

 

 

In order to prevent uncontrolled starts, switching off or changing the burner's power,

 

use 

the controller lock, which is done as follows: 
 

Touch the sensor (key) with your finger 

item 4 Fig. 6

. Pressing and holding it for 5 

seconds will cause the 

controller to lock

, the indicator diode to switch on and an extended 

audio signal to sound.

 

To unblock the hob controller, follow a similar procedure: 
 

Touch the sensor with your finger 

item 4 Fig. 6

 and hold for 5 seconds,

 

the indicator 

diode 

item

 

2 Fig. 6

 switches off, the hob controller is unlocked and an audio signal can be 

heard.

 

 

 

4.5.  Selection of pots and pans 

 

To ensure optimum use of the heat generated by the flame from the gas burner, use 

appropriate pots and pans. They must have:

 

 

- a flat bottom, 

 

- a bottom diameter larger than the diameter of the burner

.

 

 
 

In addition, the pots and pans are to be covered with lids (if permitted by the recipe). 

Also ensure that the lid does not protrude beyond the cookware, so that condensate does 
not drip onto the glass plate of the hob. This way, you will avoid difficult to remove stains. 

 

 

Do not use such cookware on the hob that extends significantly beyond the heating 

area edges. In addition, the diameters of the bottom of the pots and pans placed on the 
large and small burners  
at the front of the hob, should not exceed 22 cm. Failure to comply with this may cause the 
control panel to overheat and increase the risk of burns to the user.  
 

Cookware should be placed centrally on the grate above the centre of the burner 

before it is switched on. The minimum diameter of the cookware should not be smaller than 
the diameter of the flame crown of a particular burner. 
Pay special attention not to accidentally 

damage the temperature sensors that protrude 

above the grate,

 e.g. by moving a pot over the surface of the grates without lifting it or by 

carelessly placing cookware on the hob. 

 
NOTES - for obvious reasons: 

 

do not use plastic dishes,

 

 

do not put empty cookware on the hob's cooking zones, 

 

do not place textiles near lit burners. 

 

5. 

Hob cleaning and maintenance 

 

 

 

In the event of incorrect care for the hob's ceramic glass plate 

 

and burner elements, our warranty responsibilities are void.  

Summary of Contents for GNC-4






















Reviews: