background image

LCDI POWER CORD AND PLUG

 

 

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord and 
plug as  required by US National Electric Code 440.65. This cord consists of a length of shielded flexible cord 
with no termination on the load side and a LCDI attachment plug on the line side. 
 
The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the 
nominal     current leakage between the cord shield and either load conductor exceeds a predetermined value. 
The cord will remain de-energized until the devise has been manually reset. This is intended to reduce the risk 
of a fire in the power cord or combustible materials nearby. The cord shields are not grounded and they must 
be considered a shock hazards if  exposed. The cord shield must not be connected to ground or to any exposed 
metal. 
 
The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:  
 

1. Plug power cord into wall outlet 
2. Press TEST Button, circuit should trip, cutting power to the air conditioner  
3. Press RESET button for use 

 
If a test is performed and the indicator light remains ON, current leakage has been detected. Do not use the air            
conditioner or attempt to reset the LCDI Plug. Contact Soleus Air Powered by Gree Customer Service for trou-
bleshooting recommendations.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 

WARNING: 
 
1.  DO NOT press the TEST button while the air conditioner is operating. 

2.  The TEST and RESET buttons should not be used as 

ON

” 

and 

OFF

” 

switches. 

3.  The cord and plug are not intended to offer protection to externally connected loads or supply circuits. 
4.  The cord and plug are intended for indoor use only. 

RESET 

TEST 

 3 

Summary of Contents for GL-PAC-08E4

















Reviews: