manualshive.com logo in svg

SolarEdge SE3K-N4, Installation Manual

Share
Download
SolarEdge SE3K-N4 Installation Manual Download Page 65

RS485 Bus Configuration

To connect to the monitoring platform: 

 1.  Designate a single inverter as the connection point between the RS485 bus and the SolarEdge 

monitoring platform. This inverter will serve as the master inverter.

 2.  Connect the master to the SolarEdge monitoring platform via the LAN option (refer to 

Creating an 

Ethernet (LAN) Connection

 on page 58) or any of the other options.

To configure the RS485 bus: 

All inverters are configured by default as slaves. To configure the master:

 1.  Verify the ON/OFF/P switch is OFF.

 2.  Verify the AC is on.

 3.  Turn ON the Connection Unit.

 4.  Use SetApp to access the 

Commissioning

 main menu screen as described in 

Communication

 on page 

40.

 5.  From the main menu tap 

Communication

. The Communication screen is displayed:

Communication

Server

LAN

›

LAN

DHCP

›

RS485-1

SolarEdge Slave

›

RS485-2

Multi -Device
(Modbus)

›

ZigBee

Home Automation 

Master

›

Wi-Fi

SEDG-7E129A09-33

›

RS232

SolarEdge GSM

 

Cellular

N/A

›

GPIO

RRCR

›

Modbus 
TCP port

Disable

›

Three Phase Inverter with synergy technology Guide   MAN-01-00402-1.1

64

RS485 Bus Configuration

Summary of Contents for SE3K-N4

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands