manualshive.com logo in svg

SolarEdge SE10KUS, Installation Manual

Share
Download
SolarEdge SE10KUS Installation Manual Download Page 36

2.  Loosen the screws on the front cover of the Safety Switch , as shown below:

Figure 13: Opening the Safety Switch cover

3.  Remove the Safety Switch cover.

4.  Open the required AC and DC conduit drill guides according to the conduits used in

the installation: The drill guides are located at the bottom, back and sides of the

enclosure, each with two sizes: ¾'' and 1''. Open the required pair, taking care not

to interfere with any of the internal components. It is recommended to use a  Unibit

drill.

Figure 14: Safety Switch drill guides

NOTE

Unused conduit openings and glands should be sealed with appropriate seals.

Chapter 3: Installing the Inverter     

35

Mounting the Inverter

The inverter is typically mounted vertically, and the instructions in this

section are applicable for vertical installation. Some  three phase inverter

models can be installed horizontally (above 10° tilt) as well as vertically,

and at any tilt over 10° up to 90°. For information and instructions for

horizontal mounting refer to

http://www.solaredge.com/sites/default/files/application_note_horizontal_mounting_of_three_

 

phase_inverters.pdf.

Three

 

Phase

 

System

 

Installation

 

Guide

 

MAN-01-00527-1.

2

Summary of Contents for SE10KUS






































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands