![SolarEdge SE10k Installation Manual Download Page 51](http://html.mh-extra.com/html/solaredge/se10k/se10k_installation-manual_1313732051.webp)
Chapter 6: Communication Setup
SolarEdge Installation Guide - MAN-01-00060-2.6
50
►
To connect to the Monitoring Portal:
1
Designate a single inverter as a connection point between the RS485 bus and Monitoring Portal
1
Designate a single inverter as a connection point between the RS485 bus and Monitoring Portal
SolarEdge. This inverter will be used for master inverter.
2
Connect the master to the SolarEdge Monitoring Portal via the LAN communication options,
2
Connect the master to the SolarEdge Monitoring Portal via the LAN communication options,
ZigBee or Wi-Fi.
►
To configure the RS485 communication bus:
All inverters are configured by default as a slave. If the reconfiguration is required:
1
Make sure the ON / OFF switch is in the OFF position.
1
Make sure the ON / OFF switch is in the OFF position.
2
Turn on the AC UPS by turning the switch on the main distribution panel.
2
Turn on the AC UPS by turning the switch on the main distribution panel.
WARNING !
RISK OF ELECTRIC SHOCK, do not touch uninsulated son when the UPS cover is removed.
3
Use the User buttons to configure the connection, configure the inverter designated as
3
Use the User buttons to configure the connection, configure the inverter designated as
master, select one of the following options in the menus of the LCD:
•
Communication • Server • LAN, or Wi-Fi ZibBee
Communication • Server • LAN, or Wi-Fi ZibBee
Communication • Server • LAN, or Wi-Fi ZibBee
Communication • Server • LAN, or Wi-Fi ZibBee
Communication • Server • LAN, or Wi-Fi ZibBee
•
Conf. RS485-1 • device type •
SolarEdge
Conf. RS485-1 • device type •
SolarEdge
Conf. RS485-1 • device type •
SolarEdge
Conf. RS485-1 • device type •
SolarEdge
Conf. RS485-1 • device type •
SolarEdge
•
Conf. RS485-1 • Protocol •
Master
Conf. RS485-1 • Protocol •
Master
Conf. RS485-1 • Protocol •
Master
Conf. RS485-1 • Protocol •
Master
Conf. RS485-1 • Protocol •
Master
•
Conf. RS485-1 •
Detect. SLV
Conf. RS485-1 •
Detect. SLV
Conf. RS485-1 •
Detect. SLV
The system starts automatically detecting inverters SolarEdge slaves connected to the master inverter. The UPS
will return the correct number of slaves. If this is not the case, check the connections and connections.
4
Check the master connection to the SolarEdge Monitoring Portal, as described in
Verification
4
Check the master connection to the SolarEdge Monitoring Portal, as described in
Verification
4
Check the master connection to the SolarEdge Monitoring Portal, as described in
Verification
Creating a ZigBee connection
This communication option allows a ZigBee connection for one of the following options:
•
Connect the inverter to the SolarEdge Monitoring Portal
•
Create a bus master / slave of connected inverters
The ZigBee kit is purchased separately and comes with a user manual, which should be examined before connecting. It is
available on the website of SolarEdge at
http://www.solaredge.com/groups/products/communication
(In ZigBee)
available on the website of SolarEdge at
http://www.solaredge.com/groups/products/communication
(In ZigBee)
available on the website of SolarEdge at
http://www.solaredge.com/groups/products/communication
(In ZigBee)
Creating a Wi-Fi
This communication enables use Wi-Fi to connect the inverter to the SolarEdge Monitoring Portal.
The wireless kit can be purchased separately and assembled during the installation of the system. The wireless kit comes with
a user manual, which must be consulted before connecting. It is available on the website of SolarEdge at
http://www.solaredge.com/groups/products/communication
a user manual, which must be consulted before connecting. It is available on the website of SolarEdge at
http://www.solaredge.com/groups/products/communication
(In wireless).