SolarEdge SE-RGMTR-3D-208V-A Installation Manual Download Page 51

Page: 51 / 71

Troubleshooting the Meter using the
Device Display

The communication status screen should display the

following:

D e v P r o t # #

R S 4 8 5 - 1 < M T R > < S E > < 1 >

R S 4 8 5 - 2 < - - - > < - - > < - - >

Z i g B e e < - - - > < - - > < - - >

Device Type or Protocol are configured
incorrectly

MTR

(meter) is not displayed as the device type (DEV), or

(SolarEdge) is not displayed as the Prot (protocol), configure

the meter as follows.:

1. Select

Communication

RS485-x Conf

Device Type

Revenue Meter

2. Select Communication

RS485-x Conf

Protocol

SolarEdge

3. Check that the meter's Modbus address specified in

Communication

RS485-x Conf

Device ID

corresponds to the meters' DIP switch settings. Refer to

"DIP Switches" on page 17.

Revenue Grade Energy Meter with Modbus Connection Installation Guide MAN-01-00609-1.0

Troubleshooting the Meter using the Device

Summary of Contents for SE-RGMTR-3D-208V-A








































































Search results

Summary of Contents for SE-RGMTR-3D-208V-A

Reviews:

SolarEdge SE-RGMTR-3D-208V-A, Installation Manual, Page: 51 / 71

Search results

Summary of Contents for SE-RGMTR-3D-208V-A

Reviews: