SolarEdge SE-RGMTR-3D-208V-A Installation Manual Download Page 32 | Manualshive

Page: 32 / 71

SolarEdge SE-RGMTR-3D-208V-A Installation Manual Download Page 32

Device Configuration

This section describes basic configuration of SolarEdge devices

(inverter/Commercial Gateway) for use of a meter. In addition,

a configuration that is specific to the application being used is

required in some cases. Refer to the following documents:

Export Limitation -

https://www.solaredge.com/sites/default/files/export_

limitation_application_note_NA.pdf

StorEdge Smart Energy Management off-grid applications

-

https://www.solaredge.com/files/pdfs/storedge_backup_

installation_guide_NA.pdf

NOTE

Calculated meter readings, such as self-consumption,
are calculated using the data measured by the meter
and the inverters. Calculated meter readings are only
sent when Energy Manager is enabled (for details
refer to

https://www.solaredge.com/sites/default/files/expor
t_limitation_application_note_NA.pdf

).

Device Configuration using SetApp

NOTE

Meter functionality is supported in inverters with CPU
versions 4.2.xxx and above.

Revenue Grade Energy Meter with Modbus Connection Installation Guide MAN-01-00609-1.0

Chapter 3: Configuration

31

«
...
30
31
32
33
34
...
»

Summary of Contents for SE-RGMTR-3D-208V-A








































































Reviews:

No comments