SolarEdge SE-RGMTR-3D-208V-A Installation Manual Download Page 20 | Manualshive

Page: 20 / 71

SolarEdge SE-RGMTR-3D-208V-A Installation Manual Download Page 20

Chapter 2: Meter Installation

Installation Guidelines

AC wire specifications: 1.3 to 2.0 mm diameter / 16 to 12 AWG

stranded wire, 600 V, type THHN, MTW, or THWN.

RS485 wiring specifications:

Cable type: Min. 3-wire shielded twisted pair (a 4-wire

cable may be used)

Wire cross-section area: 0.2- 1 mm²/ 24-18 AWG (a CAT5

cable may be used)

NOTE

If using a cable longer than 10 m/33 ft in areas where
there is a risk of induced voltage surges by lightning,
it is recommend to use external surge protection
devices. For details refer to

External Lightning

Protection on page 68. If grounded metal conduit are
used for routing the communication wires, there is no
need for a lightning protection device.

The meter is considered “permanently connected

equipment” and requires a disconnect means (circuit

breaker, switch, or disconnect) and overcurrent protection

(fuse or circuit breaker).

Revenue Grade Energy Meter with Modbus Connection Installation Guide MAN-01-00609-1.0

Chapter 2: Meter Installation

19

«
...
18
19
20
21
22
...
»

Summary of Contents for SE-RGMTR-3D-208V-A








































































Reviews:

No comments