manualshive.com logo in svg

SolarEdge SE-RGMTR-3D-208V-A, Installation Manual, Page: 13 / 71

Share
Download
SolarEdge SE-RGMTR-3D-208V-A Installation Manual Download Page 13

The SolarEdge Revenue Grade Energy 
Meter with Modbus Connection 

The SolarEdge Revenue Grade Energy Meter with Modbus 

Connection (also referred to as “the meter”) enables measuring 

the power and energy of the photovoltaic (PV) system. 

The following meter models are available:

SolarEdge Meter Model

Grid Type

SE-RGMTR-3D-208V-A

Delta

SE-RGMTR-3Y-208V-A

Wye

SE-RGMTR-3Y-480V-A

Wye

The meter is used by the inverter for the following applications:

Production metering

Consumption monitoring

Export limitation

Smart Energy on-grid applications 

The meter requires 

three Current Transformers (CTs). The CTs 

are available from SolarEdge.

The SolarEdge inverter or the Commercial Gateway (CCG) reads 

the exported/imported power from a meter installed at the grid 

connection point or reads the consumption from a meter 

installed at the load consumption point. 

Revenue Grade Energy Meter with Modbus Connection Installation Guide MAN-01-00609-1.0

12

   The SolarEdge Revenue Grade Energy Meter with

Summary of Contents for SE-RGMTR-3D-208V-A








































































Reviews:

No comments