manualshive.com logo in svg

SolarEdge Firefighter Gateway, Installation Manual, Page: 16 / 61

Share
Download
SolarEdge Firefighter Gateway Installation Manual Download Page 16

Mounting and Connecting the Firefighter Gateway

The  gateway can be installed on a wall or on a DIN rail.

To mount the  Commercial Gateway on a wall:

 1.  Determine the mounting location. Leave clearance from all sides of the  gateway for 

cover opening, cable connection and routing.

 2.  Position the device on the wall, mark points through the mounting tabs and drill 

holes using a 4mm diameter drill bit.

 3.  Mount the unit using screw anchors and screws (use 3.5mm diameter screws, 20mm 

minimum length, not provided by SolarEdge). 

Figure 4: Firefighter Gateway mounting tabs

To mount the  Commercial Gateway on a DIN rail:

 1.  Press the  gateway upwards and snap it into the upper and lower edges of the DIN 

rail.  

Figure 5: Firefighter Gateway mounted on a DIN rail

 

Chapter 2: Installing the Firefighter Gateway     

16

Firefighter Gateway Installation Guide MAN-01-00113-1.4

Summary of Contents for Firefighter Gateway






























































Reviews:

No comments