manualshive.com logo in svg

SolarEdge Firefighter Gateway, Installation Manual, Page: 54 / 61

Share
Download
SolarEdge Firefighter Gateway Installation Manual Download Page 54

Appendix C: Inserting the GSM Modem in the 
Firefighter Gateway

 

NOTE

The GSM modem should be purchased separately.

To turn off the inverter, disconnect the AC and insert a SIM card:

 1.  Turn the inverter Safety Switch (if applicable) to OFF.

 2.  Turn the inverter ON/OFF switch to OFF.

 3.  Disconnect the AC to the inverter by turning OFF the circuit breakers on the 

distribution panel. Wait 5 minutes for the capacitors to discharge.

 4.  Open the Firefighter Gateway cover.

 5.  If there is no SIM card installed in the modem, insert one into the slot on the 

GSM modem.

Figure 23: Inserting the SIM card into the GSM modem 

To install the GSM modem in the Firefighter Gateway:

 1.  Insert the top of the plastic spacer through the opening in the GSM modem, as 

shown in 

Figure 24.

Figure 24: GSM modem on a Firefighter Gateway board 

 2.  Connect one end of the cable to the GSM modem connector.

Appendix C: Inserting the GSM Modem in the Firefighter Gateway     

54

Firefighter Gateway Installation Guide MAN-01-00113-1.4

Summary of Contents for Firefighter Gateway






























































Reviews:

No comments