SolarEdge Firefighter Gateway Installation Manual Download Page 48 | Manualshive

Page: 48 / 61

SolarEdge Firefighter Gateway Installation Manual Download Page 48

Appendix A: Mounting the ZigBee Plug-in in
the Firefighter Gateway

NOTE

The ZigBee Plug-in should be purchased separately.

1. Turn the inverter Safety Switch (if applicable) to OFF.

2. Turn the inverter ON/OFF switch to OFF.

3. Disconnect the AC to the inverter by turning OFF the circuit breakers on the

distribution panel. Wait 5 minutes for the capacitors to discharge.

4. Open the Firefighter Gateway cover.

5. Unscrew the nut and washer on the ZigBee Plug-in.

6. Connect the ZigBee Plug-in in a Firefighter Gateway board as shown below, and

ensure that:

the antenna connector at the end of the ZigBee Plug-in goes through the bracket.

all pins are correctly positioned in the Firefighter Gateway socket and no pins are

left out of their socket.

the card is firmly in place.

Figure 19: ZigBee Plug-in on a Firefighter Gateway board

3. Screw in the nut and washer on the ZigBee Plug-in

4. Connect the antenna.

5. Replace the Firefighter Gateway cover.

Appendix A: Mounting the ZigBee Plug-in in the Firefighter Gateway

48

Firefighter Gateway Installation Guide MAN-01-00113-1.4

«
...
46
47
48
49
50
...
»

Summary of Contents for Firefighter Gateway






























































Reviews:

No comments