manualshive.com logo in svg

SolarEdge Firefighter Gateway, Installation Manual, Page: 35 / 61

Share
Download
SolarEdge Firefighter Gateway Installation Manual Download Page 35

Communication

(1)

,

(2)

:

S e r v e r < L A N >
L A N   C o n f
R S 4 8 5 – 1   C o n f < S >
R S 4 8 5 – 2   C o n f < S >
Z i g B e e   C o n f < S >  
W i - F i   C o n f < N / A >                            
C e l l u l a r   C o n f  
S l a v e   D e t e c t

Server:

L A N
R S 4 8 5
Z i g b e e
W i - F i
C e l l u l a r
N o n e

LAN Conf:

I P   C o n f i g
S e t   D H C P   < e n >
S e t   I P
S e t   M a s k
S e t   G a t e w a y
S e t   D N S
S e t   S e r v e r   A d d r
S e t   S e r v e r   P o r t
M o d b u s   T C P < D i s >

 

(1)If ZigBee is connected, the Wi-Fi Conf menu is not displayed. If ZigBee is not connected, ZigBee Conf and Wi-Fi Conf 

are both displayed with <N/A> and their menus are not accessible.

(2)When using the SolarEdge GSM products, RS232 Conf menu is unavailable.

Firefighter Gateway Installation Guide MAN-01-00113-1.4

35

   Configuration Menu Options

Summary of Contents for Firefighter Gateway






























































Reviews:

No comments