manualshive.com logo in svg

SolarEdge Firefighter Gateway, Installation Manual, Page: 31 / 61

Share
Download
SolarEdge Firefighter Gateway Installation Manual Download Page 31

IP Status

This screen describes the Ethernet configuration: IP, Mask, TCP Gateway and MAC 

address (Media Access Control) of the Firefighter Gateway.

I P    1 9 2 . 1 6 8 . 2 . 1 1 9
M S K   2 5 5 . 2 5 5 . 2 5 5 . 0
G W    1 9 2 . 1 6 8 . 2 . 1
M A C   0 - 2 7 - 0 2 - 0 0 - 3 9 - 3 6

ZigBee Status

This screen describes the ZigBee configuration:

P A N : X X X X X
C H : X X / X X X X    R S S I : < L >
M I D : X X X X   X X
Z i g B e e   R e a d y

RSSI: The receive signal strength indication of the closest ZigBee in the system. L = 

low, M = medium, H = high and (-) = no signal.

PAN ID: The ZigBee transceiver PAN ID (Personal Area Network Identification), the 

ID uniquely represents a device in a Zigbee network.

Ch.: The ZigBee transceiver channel

ID: The ZigBee transceiver ID

MID: The Master ID of the coordinator (master) ZigBee Plug-in. This field is shown 

only in devices with router (slave) ZigBee cards, and after a successful ZigBee 

association. If a ZigBee Plug-in is not connected, a No ZigBee message is displayed 

instead of the MID field.

ZigBee Ready: This field is shown only in devices with ZigBee router transceivers 

(slaves), in a multi-point (MP) protocol configuration. If a ZigBee transceiver is not 

physically connected, a No ZigBee message is displayed.

Wi-Fi Status

This screen describes the Wi-Fi configuration:

I P :   1 9 2 . 1 6 8 . 2 . 1 1 9
G W :   1 9 2 . 1 6 8 . 2 . 1
S S I D :   x x x x x x x x
R S S I :   < L / M / H / - >  

IP: The DHCP provided address

GW: The gateway IP address

Firefighter Gateway Installation Guide MAN-01-00113-1.4

31

   Status Screens - Operational Mode

Summary of Contents for Firefighter Gateway






























































Reviews:

No comments