manualshive.com logo in svg

SolarEdge Firefighter Gateway, Installation Manual, Page: 19 / 61

Share
Download
SolarEdge Firefighter Gateway Installation Manual Download Page 19

Figure 7: 3-pin terminal block

 2.  Connect the 3-pin terminal block to the designated RS485-1 port on the Firefighter 

Gateway.

 

NOTE

RS485-1 is configured as SolarEdge device by default, therefore RS485-

1 is used as the RS485 bus connection point.

 3.  If the Firefighter Gateway is at the end of the RS485 chain, terminate the Firefighter 

Gateway by switching a termination DIP switch to ON. The switches in the SolarEdge 

Firefighter Gateway are marked SW1 for the RS485-1 port termination (and SW2), as 

shown below:

Figure 8: RS485 connectors and termination switches

 4.  Open the inverter cover as described in their manual. 

 5.  Remove the seal from one of the openings in communication gland #2 of the 

inverter and insert the cable through the opening. 

 6.  Pull out the 9-pin RS485 terminal block connector, as shown below: 

Firefighter Gateway Installation Guide MAN-01-00113-1.4

19

   Creating an RS485 Bus Connection

Summary of Contents for Firefighter Gateway






























































Reviews:

No comments