manualshive.com logo in svg

SolarEdge Firefighter Gateway, Installation Manual, Page: 15 / 61

Share
Download
SolarEdge Firefighter Gateway Installation Manual Download Page 15

The  gateway must always remain in an ambient temperature of-20°C (-4°F) to +60°C 

(140°F).

The  gateway power supply requires a socket outlet with a grid voltage of 100 V - 

240 V (50/60Hz).

Protect the  gateway from dust, wet conditions, corrosive substances and vapors.

Cable specifications:

Connection Type

Cable Type

Maximum Length

RS485 

communication 

bus (per RS485 

port)

Three twisted wires or 4-wire twisted 

pair cable (two twisted pairs).

Recommended wire size: 20 AWG / 

0.52 mm2

1,000m (3,330 ft)

Ethernet

CAT5/6

100m (325 ft).

 

NOTE

If using a cable longer than 10 m/33 ft in areas where there is a 

risk of induced voltage surges by lightning, it is recommend to 

use external surge protection devices. For details refer to: 

http://www.solaredge.com/files/pdfs/lightning_surge_protection.pdf

. If 

grounded metal conduit are used for routing the communication wires, there 

is no need for a lightning protection device. 

Installation Workflow

The following provides an overview of the workflow for installing and setting up the 

Firefighter Gateway:

Mounting the Firefighter Gateway

,  page 16

Connecting the Firefighter Gateway to the SolarEdge installation, 

 page 18

Configuring the Firefighter Gateway and inverters

, page 18

Using the Firefighter    Gateway to connect the installation to the monitoring server 

(optional)

, page 18

 

Firefighter Gateway Installation Guide MAN-01-00113-1.4

15

   Installation Workflow

Summary of Contents for Firefighter Gateway






























































Reviews:

No comments