Solare Datensysteme Solar-Log Components Connection Manual Download Page 475 | Manualshive

Page: 475 / 506

background image

475

Stiebel-Eltron

4

Stiebel-Eltron

4.1

Stiebel Eltron Heat pumps (ISG)

Termination

Addressing

Interface

No

Yes

LAN

Overview

•

Integrated interface.

•

The Stiebel-Eltron heat pump‘s IP address must be adapted.

•

Connected using network cable (patch cable) and Ethernet router or switch (when assigning a static IP ad-
dress).

•

Installation steps:

•

Assign heap pump a static IP address or via

DHCP (enabled by default).

•

Connect the heat pump to a switch (with a static IP address) or Ethernet router.

•

Connect the Solar-Log™ to a switch (with a static IP address) or Ethernet router.

Assigning IP addresses

•

Configure the address according to the manufacturer‘s manual.

•

The DHCP range (IP address) for the heat pump has to be in the same subnet as the Solar-Log™.

•

Procedure: According to the manufacturer‘s manual.

Detection via the Solar-Log™ WEB Interface

•

For detection on the Solar-Log™ , select the device class under the menu

Configuration | Device | Definition

| Interface

with the plus symbol and then select Stiebel-Eltron as the manufacturer. Confirm your selection

with

OK

.

•

Save your selections and then start the Device Detection under

Configuration | Device | Detection

.

•

After the detection, Stiebel-Eltron appears as a switching device in the

Configuration | Smart Energy | Swit-

ching Groups menu

.

•

Assign the switch contact of the Stiebel heat pump to a switching group (the switch contact only needs to be
defined in the software, no hardware is required) and configure the specific control for the heat pump. For
more information on Smart Energy such as configuration, functionality and application examples, refer to
Chapter 5.2: „Controlling Heat Pumps with a Grid Company Blocking Signal“
(

https://www.solar-log.com/manuals/manuals/en_GB/SolarLog_Manual_Smart_Energy_EN_01.pdf

).

•

The heat pump appears in the

Diagnostics | Smart Energy | Status (current)

and

history menu

(also with

several temperature values that are retrieved and recorded from the heat pump).

Detection from the Solar-Log 1200

•

When using the Solar-Log 1200, the detection can also be started from the display. Select the settings

►

Start

►

Initial Configuration

►

Page 2 „Device“

►

Add and select the manufacturer Stiebel-Eltron from there. Save

and start the Device Detection.

«
...
473
474
475
476
477
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: e-motion Pages: 22

Brand: Hach Pages: 256

Brand: MadgeTech Pages: 2

Brand: FIS Pages: 55

InSite Construction

Brand: Peri Pages: 52

Brand: B+B Sensors Pages: 18

Brand: HENGKO Pages: 78

Brand: M2MLogger Pages: 18

Brand: Racepak Pages: 2

MODAT-550A Series

Brand: IEI Technology Pages: 79

Brand: Keithley Pages: 478

OM-EL-WIN-USB Series

Brand: Omega Pages: 13

Brand: Measurement Computing Pages: 8

Brand: Wohler Pages: 28

Brand: Wohler Pages: 30

Brand: SOLIS Pages: 5

Brand: Sorel Pages: 8

Brand: SoundEar Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands