Solare Datensysteme Solar-Log Components Connection Manual Download Page 175 | Manualshive

Page: 175 / 506

background image

175

INVT iMARS

46

INVT iMARS

46.1

INVT iMARS / MG-Serie / BG-Serie

Termination

Adressing

Interface

-

Yes

RS485

Overview

•

Integrated interface

•

Connection via RS485

•

3-pin wiring

•

The communication address has to be assigned (is set to 1 by default)

•

Installation steps

•

Switch off the inverters and Solar-Log™

•

Connect inverters to the Solar-Log™

•

Connect the inverters to each other

•

Allocate communication address

Connect inverters to the Solar-Log™

The wiring is done using a

•

Self-made cable connection using the RS485 connector and the terminal block connector.

Procedure

1. If you are making the cable yourself, connect the wires as shown in the following diagram::

Solar-Log™ terminal strip connector

RS485 connector

Terminal

Pin

►

1

►

2 (RS485+)

►

3

►

4 GND

►

4

►

3 (RS485-)

2. RS485 connector an den Wechselrichter, gemäß Anleitung zum Wechselrichter, anschliessen
3. Klemmleistenstecker in RS485-Buchse des Solar-Log™ stecken

Connect the inverters together

•

Start according to the inverter‘s instructions.

Assign the communication address

•

Start according to the inverter‘s instructions.

«
...
173
174
175
176
177
...
»

Summary of Contents for Solar-Log



























































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Solar-Log

Brand: UNI-T Pages: 2

SePem 01 Master

Brand: sewerin Pages: 78

Brand: Microedge Instruments Pages: 64

Brand: Extech Instruments Pages: 15

Brand: Endress+Hauser Pages: 14

Squirrel 2020 Series

Brand: Grant Datalogging Pages: 17

Brand: Fimer Pages: 29

Brand: Race Result Pages: 7

Brand: FAG Pages: 122

Brand: pico Technology Pages: 34

Brand: Radionode Pages: 51

Brand: Ebro Pages: 24

Brand: Omega Pages: 10

Brand: Ebro Pages: 49

Brand: ICP DAS USA Pages: 185

Brand: Ebro Pages: 24

Brand: Telemotive Pages: 71

Brand: Sensitech Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands