Solar Stik PSS-G Deployment Manual Download Page 43

Page: 43 / 141

August 2020

Solar Stik

Inc.

PSS-G/RAID Alternative Energy System Deployment Guide

Connect the two (2) Inter-Connect Strips to the 24VDC In port on front-left corner of the PRO-Verter
7000 AGS using two (2) 5’ Inter-Connect Cables.

4 Connect Expander Paks to PRO-Verter

Inter-Connect Strip

Li Expander

Pak 2400 (x3)

PRO-Verter

7000

PRO-Verter 7000

Figure 23. Expander Pak to PRO-Verter 7000 AGS connection

Legend

Inter-Connect

Direction of flow energy or comm

5 Connect PRO-Verter Power Hub 2400

Use a 5’ Inter-Connect Cable to connect the Power Hub 24VDC Batt/PRO-Verter

port and the PRO-

Verter’s 24VDC port on the right-hand side.

Power Hub 2400

PRO-Verter

7000 AGS

(right-side view)

24VDC Power Hub 2400

PRO-Verter 7000 AGS

Legend

Inter-Connect

Direction of flow energy or comm

Li Expander

Pak 2400 (x4)

Figure 24. Power Hub 2400 to PRO-Verter 7000 AGS connection

Summary of Contents for PSS-G














































































































































Search results

Summary of Contents for PSS-G

Reviews:

Related manuals for PSS-G

Brands by name

Popular brands

Solar Stik PSS-G, Deployment Manual

Search results

Summary of Contents for PSS-G

Reviews:

Related manuals for PSS-G

Brands by name

Popular brands