1. FEATURES
Wireless sensor Ajax DoorProtect is designated for doors and windows opening detection.
It functions as a part of Ajax security system.
SPECIFICATION
MEANING
Sensor type
wireless
Assembling type
removable
Operating level
1 cm (0.4 in) (small magnet), 2 cm (0.8 in)
(big magnet)
Uses
indoors
Socket to plug in the wire sensors
available
Tamper protection button
available
Radio signal power
20 mW
Radio-frequency range
868 MHz (Europe); 915 MHz (USA)
Maximum distance between sensor
and central unit
2000 m (6562 ft) (open area)
Power supply
CR123A battery
Power supply voltage
3V
Battery life
Up to 7 years
Operation temperatures range
from 0°С (+32°F) to +50°С (+122°F)
Operation humidity
up to 80%
Dimensions
Ø20х90 mm (0.78x3.54 in)
4. SETTING-UP PROCEDURES
4.1 Before installing the sensor, it is required to register it with the Ajax security system. In
order to register the sensor, it is necessary to switch the Ajax security system’s receiver to
«Add Device» mode (the receiver’s manual explains how to accomplish it) and to put the
switch «2» (PICTURE 3) on the sensor to the «ON» position. Sensor’s light must blink at the
moment of switching on. The registration request is transmitted at the moment the sensor
is switched on only! In case the registration was not successful, switch off the sensor, wait for
5 seconds and switch it on again. If the sensor’s light blinks constantly (each second during
one minute), it means that the sensor is not registered. The light blinks in the same way if the
sensor is deleted from the registration list. Non-registered sensor blinks also throughout 3
seconds during each activation.
4.2 Having registered the sensor successfully, select an appropriate location to install it.
2. SPECIFICATIONS
ATTENTION!
Make sure that in the installation location sensor has a stable radio contact with the
receiver! A maximum distance of 2000 m (6562 ft) between the sensor and the cen-
tral unit is mentioned as a comparison with other devices. This distance was found
as a result of open area tests. Connection quality and distance between the sensor
and the receiver can vary depending on installation location, walls, compartments,
bridgings, as well as the thickness and constructional material. Signal coming
through obstacles, loses power. For example, distance range between the sensor
and receiver, divided with two reinforced concrete bearing walls, constitutes approx-
imately 30 m (98.4 ft). Please note that moving the sensor alongside the doors even
10 cm (4 in), it is possible to improve the signal reception considerably.
DoorProtect
Make sure to check the signal strength! It is possible to launch a signal level test on the
receiver’s side. Test launching is described in the receiver’s manual.
ATTENTION!
Signal level test and detection zone test for sensors take some time to start. A certain
period of time is necessary for the receiver to send a test request to the sensor, and for
the sensor to send a test response.
RECEIVER
SENSOR'S LIGHT EMITTING DIODE DESCRIPTION
3 indication bars
lights almost permanently, with short
breaks each 1.5 seconds
excellent signal
2 indication bars
blinks 5 times per second
medium signal
1 indication bar
blinks twice per second
low signal
0 bars
short fl ashes each 1.5 seconds
no signal
5. INSTALLATION
5.1 In order to assemble the sensor and the big magnet, lift up the plastic SmartBracket
panel with your fi nger (PICTURE 1), move it alongside the frame and remove it.
In order to assemble the small magnet, take its fastening clip out of the frame lifting it up
with a screwdriver (PICTURE 2).
3. COMPONENTS
DoorProtect opening detection sensor, magnet, external contact, battery CR123A,
installation set, manual
QR
QR
PICTURE 1. The sensor’s
and the big magnet’s
fastening clip
Move down
and
lift up
PICTURE 2.
Small magnet
assembling
Solar
Plus
Ajax
DoorProtect
Solar
Sikring