manualshive.com logo in svg

Sokkia iX-1001, Operator'S Manual, Page: 70 / 177

Share
Download
Sokkia iX-1001 Operator'S Manual Download Page 70

66

12. DISTANCE MEASUREMENT

The color and flashing speed of the guide light indicates the status of the instrument and can be known when 
the user is located at a distance from the instrument.

Switching the guide light ON/OFF "5.1 Basic Key Operation" 

• The pattern of the guide light can be changed.

"19.7 Instrument Conditions - Instrument"

• Even if the guide light is set to ON, the guide light is OFF during distance measurement with the target type 

"N-Prism" or returned signal checking.

Guide light status and meaning

Status of the instrument 

An angle can be measured at the same time as distance.

• The search range can be set.

"10.1 Auto Pointing and Auto Tracking Settings"

 

Caution

• The laser beam is emitted during Auto Pointing and Auto Tracking.

PROCEDURE

1. Face the instrument in the direction of the target

Use the sighting collimator to aim the instrument 
and telescope toward the target.

"10. TARGET SIGHTING AND 

MEASUREMENT"

12.2 Using the Guide Light in Distance Measurement

Light status

Meaning

Slow flashing (Red and green 
simultaneously)

Waiting
Search error (error screen only)

Fast flashing (Red and green 
simultaneously)

Searching in progress
Measuring (continuous measurement)
Returned signal checking in progress
Auto Tracking in progress (Auto Tracking model only)
Auto Tracking in predicted direction (Auto Tracking model only)

Green and red alternate flashing

Distance measurement error (no signal, sighting error)
"Prism wait"

12.3 Distance and Angle Measurement

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments