Sokkia iX-1001 Operator'S Manual Download Page 67

Page: 67 / 177

11. ANGLE MEASUREMENT

• The following operation can be select by

switching the Operating icons.

[COORD]

: set the angle by coordinates

[INV]

: rotate the top of the instrument and

telescope 180

[CNFG]

: : set motor settings



"10.1 Auto Pointing and Auto Tracking
Settings"

• The following Operating icons are also available

on the Auto Tracking model combined with the
remote controller.

[RC]

: Rotates directly in the direction of the

Remote Controller

[<-RC]

: Rotates in a counterclockwise

direction (from the point of view of the
Remote Controller)

[RC->]

: Rotates in a clockwise direction (from

the point of view of the Remote
Controller)

[RC Cont]

: Nullifies the current measurement

position then continues Turning
operation/

The following explains angle measurement and the features used to output measurement results to a computer
or other external devices.



Setting procedures: "9. CONNECTING TO EXTERNAL DEVICES"



Cables: "25. ACCESSORIES"



Output format and command operations: "Communication manual"

PROCEDURE

1. Connect instrument and external device.



Setting procedures: "9. CONNECTING TO

EXTERNAL DEVICES"

2. Allocate the

[HVOUT-T]

[HVOUT-S]

Operating

icon to the Observation mode screen.



"19.12 Allocating Operating Icons"



• Pressing the Operating icon outputs data in the

following format.

[HVOUT-T]

:GTS format

[HVOUT-S]

: SET format

3. Sight the target point.

4. Press

[HVOUT-T]

[HVOUT-S]

Output measurement data to peripheral
equipment.

11.4 Angle measurement and Outputting the Data

Summary of Contents for iX-1001


















































































































































































Search results

Summary of Contents for iX-1001

Reviews:

Sokkia iX-1001, Operator'S Manual, Page: 67 / 177

Search results

Summary of Contents for iX-1001

Reviews: