Sokkia iX-1001 Operator'S Manual Download Page 64 | Manualshive

Page: 64 / 177

Sokkia iX-1001 Operator'S Manual Download Page 64

60

11.ANGLE MEASUREMENT

This section explains the procedures for basic angle measurement in Observation mode.
• It is possible to allocate Operating icons in measurement menus to suit various applications and the ways that

different operators handle the instrument.

"19.12 Allocating Operating Icons"

Use the “0SET” function to measure the included angle between two points. The horizontal angle can be set
to 0 at any direction.

PROCEDURE

1. Sight the first target as at right.



"10. TARGET SIGHTING AND
MEASUREMENT"

2. Press

[0SET]

.

[0SET]

will flash, so press

[0SET]

again.

The horizontal angle at the first target becomes 0°.

3. Sight the second target.

The displayed horizontal angle (HA-R) is the
included angle between two points.

11.1 Measuring the Horizontal Angle between Two Points (Horizontal Angle 0°)

«
...
62
63
64
65
66
...
»

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments