manualshive.com logo in svg

Sokkia iX-1001, Operator'S Manual, Page: 29 / 177

Share
Download
Sokkia iX-1001 Operator'S Manual Download Page 29

25

5. BASIC OPERATION

(4) Laser-pointer/guide light icon

Selection of laser-pointer/guide light status.

Switching the laser-pointer/guide light ON/OFF: "5.1 Basic Key Operation"

You can jump to the Instrument config. screen.

"19.7 Instrument Conditions - Instrument"

: Guide light ON
: Guide light OFF
: Laser-pointer ON
: Laser-pointer OFF

• The laser-pointer will be automatically switched OFF during distance measurement.

(5) Tilt angle compensation icon

The vertical and horizontal angles are automatically compensated for small tilt errors using the dual-axis tilt 
sensor.
Selection of tilt function condition.
You can display <Tilt> or jump to the Angle/tilt config. screen.

<Tilt>: "7.2 Levelling"

Setting of tilt angle compensation: "19.1 Observation Conditions - Angle/Tilt"

: Horizontal and vertical tilt angles compensated (blue)
: No compensation 
: Only vertical tilt angle compensated (green)

•

 is displayed when the instrument is out of level.

(6) Communication status with external devices icon

Selection of communication method with external devices.
You can jump to the Communication config. screen.

Setting of RS232C communication: "9.3 Connection via RS232C Cable"

Setting of 

Bluetooth

 communication: "9.1 Wireless Communication using Bluetooth Technology"

: Connection via RS232C cable
: Connection via 

Bluetooth

 wireless technology

Connection status to external devices is displayed as follows.
i) Connection via 

Bluetooth

 wireless technology

: Connecting

: Canceling connection

: (Antenna is moving) Inquiring about other 

Bluetooth

 devices

: (Antenna is stationary) Communication settings in progress/Preparing for communication 

(Instrument just powered ON etc.)

: Connection error (icon flashes)

Summary of Contents for iX-1001


















































































































































































Reviews:

No comments