manualshive.com logo in svg

Sofar solar 3K-6KTLM-G2, User Manual

Share
Download
Sofar solar 3K-6KTLM-G2 User Manual Download Page 27

SOFAR 3K~6KTLM-G2

User manual

Copyright © Shenzhen SOFARSOLAR Co., Ltd

- 22 -

4.2. Connecting PGND Cables

Connect the inverter to the grounding electrode using protection ground

(PGND) cables for grounding purpose.

The inverter is transformer-less, requires the positive pole and

negative pole of the PV array are NOT grounded. Otherwise it will cause
inverter failure. In the PV power system, all non current carrying metal
parts (such as: PV module frame, PV rack, combiner box enclosure,
inverter enclosure) should be connected to earth.

Attention

Prerequisites:

The PGND cables are prepared (

≥

5mm

²

outdoor power cables are

recommended for grounding purposes),the color of cable should be
yellow-green.

Procedure:

Step 1

Remove the insulation layer with an appropriate length using a wire

stripper, as shown in Figure 4-2.

Figure4-2 Preparing a ground cable (1)

Note

：

L2 is 2 to 3mm longer than L1

Step 2

Insert the exposed core wires into the OT terminal and crimp them

by using a crimping tool, as shown in Figure 4-3.

Figure4-3 Preparing a ground cable (2)

Summary of Contents for 3K-6KTLM-G2
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands