Soehnle Professional 3035 Page 42 Manual Download

Page: 42 / 124

5.8 Tenfold display x10

Shows the weight value with another decimal in 10 times higher resolution.

Switch to the setting function level with the function change key.

Gross

x 10

Aux.

display

Prog-

ram

Setup

mode

F 1

F 2

F 3

F 4

F 5

F 6

Press the F2 x10 key.

Approvable scales

If the scale has been calibrated as verifiable, the tenfold higher resolution appears as long as the x10 key is

held down. After the key is released, the x10 display switches off after 5 seconds.

Non-approvable scales

If the scale is not calibrated for use in legal metrology, the tenfold higher resolution appears constantly in the

display. Pressing the key, switches on the tenfold higher resolution. Pressing another key switches the

tenfold higher resolution off again.

As long as the tenfold higher display is switched on, X10 appears in the symbol bar. When the machine is

turned off, the function is disabled.

In the setting mode, you can set the tenfold higher display to be constantly displayed for one weighbridge.

The function setting mode/scale/scale parameters/control mode/on switches the x10 display constantly on

and deactivates the x10 key.

Prerequisite: Scale is not approvable. The factory setting is "Function off".

Summary of Contents for 3035





























































































































Search results

Summary of Contents for 3035

Reviews:

Related manuals for 3035

Brands by name

Popular brands

Soehnle Professional 3035, Manual

Search results

Summary of Contents for 3035

Reviews:

Related manuals for 3035

Brands by name

Popular brands