Soehnle Professional 3035 Manual Download Page 40

Page: 40 / 124

5. BASIC FUNCTIONS

5.1 Switching on

For a detailed description of how to switch on the terminal, refer to chapter 2.5 on page 13.

5.2 Switching off

For a detailed description of how to switch off the terminal, refer to chapter 2.5 on page 13.

5.3 Program selection

Selection among the available application programs.

Switch to the setting function level with the function change key.

Gross

x 10

Aux.

display

Prog-

ram

Setup

mode

F 1

F 2

F 3

F 4

F 5

F 6

Press the F5 Program key.

You can now choose from 10 different application programs.

Select a program: Key F3 arrow up / Key F4 arrow down

Start the selected program: Press F6 Accept.

Information on all user programs in chapter 6.

5.4 Zeroing

Zeroing corrects small deviations from the zero point, e.g. due to contamination of the scale.

Press the zeroing key .

The following symbol appears in the toolbar when the display is zero:

Zero setting range calibratable and non calibratable: -1 to +3% of weighing range.

If zeroing is not possible, the error message "Above zero setting range" or "Below zero setting range" appears

for two seconds.

Zero tracking

Zero tracking automatically corrects small deviations from the zero display.

In the setting mode under scale / scale parameters the zero tracking can be switched on or off (on = 0.5

d/sec calibratable and 2d/sec non calibratable).

Summary of Contents for 3035





























































































































Search results

Summary of Contents for 3035

Reviews:

Soehnle Professional 3035, Manual, Page: 40 / 124

Search results

Summary of Contents for 3035

Reviews: