Sodex Sport S30158 Assembly Instructions Manual Download Page 1

 1

 

 1

 

 

DETAILS

 

SODEX INTERNATIONAL

 

18 rue de l

avenir –

 

Bât. 224

 

14650 CARPIQUET

 

Tel: + 33 (0) 2.31.53.78.70

 

Email: [email protected]

 

 

DESCRIPTION

 

Structure en alu D90

 

Plastifié

 

 

 

CONFORM

 

European standard

 

 

NF EN 1271

 

 

 

ASSEMBLY INSTRUCTIONS

 

VOLLEYBALL POSTS, TO SEAL, D90, 

CAPSTAN TENSION

 

PRODUCT REF

:

 

S30158

 

PAIR

 

ASSEMBLY TIME

 

The time to make the assembly of this volleyball posts is estimated for 2 persons, at 30minutes. (without sealing).

 

MAINTENANCE

 

 

The equipement has to be regularly maintained by the owner. It is adviced to:

 

-

 Check every week that all the screws are correctly tightened

 

-

 Fix paint defects if the module has been damaged, using the adapted paint, specified by the manufactu-

rer.

 

-

 Replace all damaged or missing parts with a spare part recommended by the manufacturer. 

 

-

 Clean the product by using dishwasher soap, clean water, and soft cloth.

 

WARRANTY

 

 

One full year parts and labor guarantee. Every claim regarding the condition of the delivered equipment has to be 

done within the legal period,of the reception of the material.

 

The warranty will not apply to:

 

    

-

    All degradation during the transport.

 

    

-

    All degradation due to poor maintenance.

 

    

-

    All degradation due to use differing from which was intended

 

    

-

    Any defect claimed after the end of the legal period.

 

    

-

    Any damage due to a faulty installation or assembly of the module

 

 

 

Summary of Contents for S30158









Reviews: