© 2021 by Snow Joe
®
, LLC
All rights reserved. Original instructions.
SAVE THESE INSTRUCTIONS
1
EN
A Division of Snow Joe
®
, LLC
OPERATOR’S MANUAL
Model 24V-WDV6000-CT
Form No. SJ-24V-WDV6000-CT-880E-M
R
CORDLESS PORTABLE
WET/DRY VAC – TOOL ONLY
24V MAX* | 5.3 GAL
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Any electrical appliance can be dangerous if used incorrectly.
Some of the safety precautions given in this manual apply
generally to many appliances. Other warnings are specific to
the use of this cordless wet/dry vacuum.
Always follow these safety guidelines. Failure to do so may
result in personal injury or property damage.
m
WARNING!
This unit can be dangerous! Careless or
improper use can cause serious injury.
General Safety
FOR HOUSEHOLD USE ONLY
Before using, be sure that everyone using this tool reads
and understands all safety instructions and other information
contained in this manual. Save this manual and review it
frequently prior to using this tool and when instructing
others on the proper operating procedures.
Before using the wet/dry vacuum, take the time to familiarize
yourself with the controls, especially how to stop the wet/dry
vacuum in an emergency. The only individuals who should
use the wet/dry vacuum are those who have a thorough
understanding of the instructions and who know how to
operate the machine. Children should never be allowed access
to the wet/dry vacuum.
Retain this manual for future reference.
1. Keep
filters
in place – Ensure that the equipment is
assembled correctly and the filters are in the correct
position.
2. Keep bystanders and children away – All bystanders,
including children and pets, should be kept a safe
distance away from the work area.
3. Disconnect tool – Remove the battery from the battery
compartment when not in use, before servicing, when
transporting, or when changing accessories.
4. Do not use in dangerous environments – Do not operate
the wet/dry vacuum in gaseous or explosive atmospheres
or use the wet/dry vacuum to pick up flammable or
combustible liquids. Motors in these tools normally spark,
and the sparks might ignite fumes.
5. Check for damaged parts – Before using the wet/dry
vacuum, repair or replace any part that is damaged. In
addition, check any other conditions that may affect the
tool's operation.
6. Avoid unintentional starting –
Make sure the switch is off
before inserting the battery.
7. Use the right tool – Do not force the tool or any
attachment on the tool to do a job for which they were
not designed.
8. Wear face or dust masks – If operated in dusty
environment, the use of a face or dust mask specially
designed to filter out microscopic particles is
recommended.
9. Maintain tools with care – Keep tools clean for best
and safest performance. Follow instructions for changing
accessories. If the appliance is not working as it should,
or has been dropped, damaged, left outdoors, dropped
into water, please call Snow Joe
®
+ Sun Joe
®
customer
service center at 1-866-SNOWJOE (1-866-766-9563).
10. Use recommended accessories – Consult the owner’s
manual for recommended accessories. The use of
improper accessories may cause risk of injury.
11. Do not force the appliance – It will do the job better and
with less likelihood of a risk of injury if it is used at the rate
for which it was designed.
12. Do not overreach – Keep proper footing and balance
at all times.
13. Store idle tool indoors – When not in use, the wet/dry
vacuum should be stored indoors in a dry and locked-up
place out of the reach of children.
14. Stay alert – Watch what you are doing. Use common
sense. Do not operate the wet/dry vacuum when you
are tired or under the influence of drugs, alcohol or
other
medication.
m
DANGER!
Do not manually place objects into the
vacuum inlet while operating the unit, as this can seriously
damage the unit and/or harm the operator. Keep both hands
away from the air inlet while the power is on.
DO NOT ATTEMPT to remove material or hold material to be
vacuumed when the wet/dry vacuum is on. Make sure the wet/
dry vacuum
is off when clearing jammed material from the
vacuum inlet.