background image

Safety Symbols

The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions

on the machine before attempting to assemble and operate.

Spark Arrester

WARNING

This machine is equipped with an internal combustion

engine and should not be used on or near any

unimproved forest-covered, brush covered or grass-

covered land unless the engine!s exhaust system is

equipped with a spark arrester meeting applicable

local or state laws (if any).

When a spark arrester is used it should be maintained in effective

working order. The State of California requires this by law (Section

4442 of the California Public Resource Code). Other states may

have similar laws. Federal laws apply on federal lands.

Symbol

Description

READ THE OPERATOR!S MANUAL(S) Read, understand and 

follow all instructions in the manual(s) before attempting to 

assemble and operate.

WARNING! ROTATING BLADES Keep hands out of inlet and 

discharge openings running. There are rotating blades inside.

WARNING! ROTATING BLADES Keep hands our of inlet and 

discharge openings while machine is running. There are rotating 

blades inside.

WARNING! ROTATING AUGER Do not put hands or feet near 

rotating parts, in the auger/impeller housing or chute assembly. 

Contact with the rotating parts can amputate hands and fee.

WARNING! THROWN OBJECTS This machine may pick up and 

throw objects which can cause serious personal injury.

WARNING! GASOLINE IS FLAMMABLE

Allow the engine to be cooled at least two minutes before refueling.

WARNING! CABBON MONOXIDE Never run an engine indoors or 

in a poorly ventilated area. Engine exhaust contains carbon monoxide, 

an odorless and deadly gas.

WARNING! ELECTRICAL SHOCK

Do not use the engine!s electric starter in the rain.

5

MODEL SJ803

Clearing width - 21"
Clearing depth - 10"/250mm
Engine displacement - 179cc 
Torque - 9 Nm
Fuel tank volume - 2.7 L (0.71 US
gal.) unleaded gasoline
Oil reservoir capacity -

0.6L/0.63 Quart

MODEL SJ805

Clearing Width - 21"

Clearing depth - 10"/250mm

Engine displacement - 208cc

Torque -11.0 Nm

Fuel capacity - 2.7L(0.71 US

gal.) unleaded gasoline

Oil reservoir capacity -

0.6L/0.63 Quart

Technical Data

SJ_803_MANUAL ENG_R_Layout 1  9/2/10  2:23 PM  Page 5

Summary of Contents for MAX SJ803





















Reviews: