background image

20

A Two-Year Full Warranty 

for residential use 

in the United States and Canada

General Conditions:

Snow Joe, LLC warrants this product to the original purchaser for two years against defects in material or workmanship when used for

normal residential purposes. Snow Joe, LLC will repair any defect in material or workmanship, and repair or replace any defective part,

subject to the conditions, limitations, and exclusions set forth herein. Such repair or parts replacement will be free from charge to the origi-

nal purchaser except noted below.
The duration of the warranty applies only if the product is put to personal use around the household or residence. If the product is put to

any business use, commercial or industrial, then the duration of this warranty is 90 days from the date of original purchase. If any product is

rented or leased, the duration of the warranty is 90 days from the date of original purchase. 
It is the owner!s responsibility to perform correctly all maintenance, and minor adjustments explained in the owner!s manual. 

Electric Products: 

To obtain a replacement electric powered unit or repair the existing electric powered unit, you must return the complete unit and

postage prepaid to: Snow Joe Return Center, 86 Executive Avenue, Edison, NJ 08817

Gasoline / Battery Products: 

Limitations

!

Batteries are warranted only for the period of 12 months after the date of purchase on a prorated basis. Rechargeable batteries

will be replaced free from charge during the first 90 days. After the initial 90 days, batteries will be replaced at prorated 

cost to the customer

!

Idlers, cables, and electrical components are warranted to the original purchaser for use at household or residence for a period 

of two years

Exclusions

!

Snow Joe brand engines are covered under this warranty. All other engines and engine accessories are covered only by 

the engine manufacturer!s warranty and are not covered by this warranty

!

Parts used that are not genuine Snow Joe parts are not covered by this warranty

!

Damages resulting from misuse, alteration, improper assembly, improper adjustment, neglect, or accident which requires repair 

is not covered under this warranty

!

Belts and augers are not covered under warranty – belts and augers wear out and can be purchased at the Snow Joe Center.

Snow Joe, LLC may from time to time change the design of its products. Nothing contained in this warranty shall be construed as obligating

Snow Joe, LLC to incorporate such design changes into previously manufactured products, nor shall such changes be construed as

an admission that previous designs were defective.
This warranty is intended to cover product defects only. Snow Joe, LLC is not liable for indirect, incidental, or consequential damages in

connection with the use of the Snow Joe Products covered by this warranty. This warranty does not cover any cost or expense incurred

by the purchaser in providing substitute equipment or service during reasonable periods of malfunction or non-use of this product, while

waiting for completion of repairs under this warranty. Some states do not allow exclusions of incidental or consequential damages, so the

above exclusions may not apply in all states. This warranty may give you specific legal rights in your state.

If you wish to contact Snow Joe, please direct inquiries to the: 

Customer Service Department 

Snow Joe Center

86 Executive Avenue

Edison, NJ 08817

Customers who have purchased Snow Joe products exported from the United States and Canada should contact their Snow Joe

Distributor (Dealer) to obtain information applicable for your country, province, or state. If for any reason, you are not satisfied with the

distributor!s service, or if you have difficulty obtaining warranty information, contact your Snow Joe seller. If in the event your efforts are

unsatisfactory, please write to the Snow Joe Center at the above address.

If you have any questions about your product warranty, please call 1-866-SNOW-JOE or visit us online at www.snowjoe.com.

SJ_803_MANUAL ENG_R_Layout 1  9/2/10  2:24 PM  Page 20

Summary of Contents for MAX SJ803





















Reviews: