Vehicle Harness Wiring Instructions
Model # SP-2200
4UFQ
Take harness asse
m
bl
y
and route fro
m
the rear of the vehicle to the front. Route harness along fra
m
e and attach to
fra
m
e holes and fra
m
e supports. It is not reco
mm
ended to attach to fuel or brake lines for obvious reasons. Do not route
close to e
x
haust s
y
ste
m
or engine, even though Snow
&
x
¥
uses high te
m
perature wiring. It still could
m
elt under e
x
tre
m
e heat and
short the spreader electrical s
y
ste
m
as well as the vehicle electrical s
y
ste
m
.
4UFQ
Mount rear plug above hitch plate using supplied bolts, locate between hinges
JNQPSUBOU.BLFTVSFXJSJOHBOE
4UFQ
Secure harness fro
m
the rear to the front using heav
y
dut
y
t
y
-wraps or fra
m
e clips along the fra
m
e and lighter dut
y
t
y
-wraps eve
SZ
where else.
4UFQ
Drill a 1-1/4 hole in the firewall or use e
x
isting access hole
DIFDLUPNBLFTVSFZPVBSFDMFBSPOUIFPUIFSTJEFZPV
JOUFOEUPESJMM
Route connector and harness through hole. The power harness fro
m
control bo
x
to batter
y
will need to be routed
fro
m
the inside of the cab to the batter
y
– this results fro
m
the large a
m
perage connector. Route leads with lugs to batter
y
,
do not connect power at this ti
m
e.
4UFQ
Connect harness to the back of the controller and
m
ount to a suitable location. NOTE: You
m
a
y
want to contact
custo
m
er before
m
ounting controller as so
m
e prefer not to have holes drilled into the dashboard. T
y
-wrap loose
controller harness and
m
ove to the engine co
m
part
m
ent. Do not
m
ount close to an
y
heater vents.
4UFQ
Connect power leads to the batter
y
: Red + Positive, Black – Negative, alwa
y
s connect to the pri
m
ar
y
batter
y
if using a dual
batter
y
s
y
ste
m
, secure loose loo
m
to an
y
other large or
m
ediu
m
vehicle harness with
m
ediu
m
dut
y
t
y
-wraps; this will secure
wiring harness.
4UFQ
Push the ON/OFF button on the controller to check for power, when that has been confir
m
ed turn power OFF. The
electrical portion of the installation is co
m
plete.
Work Light Wiring Instructions
4UFQ
Take light kit harness and route fro
m
the rear of the vehicle (left side) to the front. Follow
m
ain spreader wire route
into
vehicle cab and locate ne
x
t to control
m
ounting position.
4UFQ
Mount rear power plug ne
x
t to
m
ain spreader power plug. Install work light onto spreader (see fig. 1 below) and also
c
POOFDU
adapter to light asse
m
bl
y
. Do not connect light adapter to
m
ain vehicle harness at this point.
4UFQ
Attach Vehicle harness (pos +) lead to supplied switch. Ne
x
t attach (pos +) lead co
m
ing off
m
ain control input power
lea d
UPTXJUDI5IFGJOBMDPOOFDUJPOXJMMCFUPDPOOFDUUIF OFH
4UFQ
Connect work light adapter to vehicle plug, test work light b
y
switching toggle on/off.
*.1035"/5%POPUNPEJGZIBSOFTTMFOHUI"OZ
NPEJGJDBUJPOTXJMMWPJEXBSSBOUZ
QMVHBSFDMFBSPGEVNQCPEZQJODIQPJOUT"QQMZBTNBMMBNPVOUPGEJFMFDUSJDHSFBTFUPDPOUBDUT
XJSFGSPNUIFWFIJDMFIBSOFTTUPUIFNBJODPOUSPM
JOQVUQPXFSMFBE#PUIUIF QPTBOE OFHDPOOFDUJPOQPJOUTXJMMCFNBMFGFNBMFJOTVMBUFETQBEFUFSNJOBMT
/LW1R5HY
18
-XO\
Summary of Contents for SP-2200
