background image

11. Fire Fighting and Chemical Containment

Hazardous Components

The EPV may con tain some or all the fol low ing ma -
te ri als and ob jects that po ten tially could be come
sig nif i cant  fire  or  en vi ron men tal  haz ards  dur ing  the
life time of the EPV:

1. Antifreeze (ethylene glycol)

2. Battery, lead/acid

3. Diesel fuel

4. Foam in tires

5. Gasoline

6. Hydraulic oil

7. Liquefied petroleum gas

8. Motor oil

The rest of this chap ter lists man u fac tur ers in for -
ma tion you will need if you ever have to con trol any
of the above items dur ing an up set or emer gency.

Antifreeze (UN 1993)

Fire extinguishing media:

Dry Chem i cal, foam, or CO2.

Special fire fighting procedures:

Wa ter spray may be in ef fec tive on fire but can pro -
tect fire fight ers and cool closed con tain ers. Use
fog noz zles if wa ter is used.

DO NOT enter confined fire space without
full bunker gear. (Helmet with face shield,
bunker coats, gloves & rubber boots). Use a
NIOSH approved positive pressure self
contained breathing apparatus. Keep
container tightly closed. Isolate from
oxidizers, heat  and open flame.

Spill or leak:

Small - mop up with ab sor bent ma te rial and  trans -
fer to hood.

Waste disposal method:

Small - evap o rate un til all va pors are gone. Dis -
pose  of  re main der  by  le gally  ap pli ca ble  methods.

Battery, Lead/Acid (UN 2794)

Extinguishing media:

Dry chem i cal, foam, or CO2.

Special fire fighting procedures:

Use pos i tive pres sure, self con tained breath ing ap -
pa ra tus.

Unusual fire and explosion hazards:

Hy dro gen and ox y gen gases are pro duced in the
cells  dur ing  nor mal  bat tery  op er a tion.

Hydrogen gas is flammable and oxygen
supports combustion. These gases enter
the air through the vent caps. To avoid the
chance of a fire or explosion, keep sparks
and other sources of ignition away from the
battery.

Spill or leak:

Re move  com bus ti ble  ma te ri als  and  all  sources  of
ig ni tion. Con tain spill by diking with soda ash (so -
dium car 

bon 

ate) or quick 

lime (cal 

cium ox 

ide).

Cover spill with ei ther chem i cal. Mix well. Make
cer tain mix ture is neu tral then col lect res i due and
place in a drum or other suit able con tainer. Dis -
pose of as hazardous waste.

ALWAYS wear acid resistant boots, face
shield, chemical splash goggles, and acid
resistant gloves when handling acid spills or 
leaks.

NOTE

DO NOT

 release UN-neutralized acid!

Waste disposal method:

Sul fu ric  Acid:

 Neu tral ize as above for a spill, col -

lect res i due, and place in a drum or suit able con -
tainer. Dis pose of as haz ard ous waste.

NOTE

DO NOT

 flush lead contaminated acid to sewer.

Waste disposal method

Bat ter ies:

 Send to lead smelter for rec la ma tion fol -

low ing  ap pli ca ble  fed eral,  state,  and  lo cal  reg u la -
tions.

Diesel Fuel (NA 1993)

Extinguishing media:

Use wa ter spray, dry chem i cal, foam, or CO2.

EPV Series – 1596(A)

Rev A

page  11 - 1

DANGER

DANGER

DANGER

Summary of Contents for EPV Series


























































Reviews: