Snorkel A46JRT, Operator'S Manual

Page: 13 / 56

Chapter 3 – Safety
A46JRT – 0261169 9
Tip-Over and Falling Hazards
Operate the aerial platform only on a firm, flat, level sur-
face capable of withstanding all load forces imposed by
the aerial platform in all operating conditions. Refer to
the General Specifications chart for the maximum wheel
load and ground pressure. Raise the booms only when
the aerial platform is on level ground.
Danger
The aerial platform can tip over if it becomes unstable.
Death or serious injury will result from a tip-over ac-
cident. Do not drive or position the aerial platform for
elevated use near any drop-off, hole, slope, soft or
uneven ground, or other tip-over hazard.
All platform occupants must wear a fall restraint device
connected to a lanyard anchor point.
It is best not to transfer from the platform to another
structure or from the structure to the platform, unless
that is the safest way to do the job. Judge each situation
separately taking the work environment into account. If
it is necessary to transfer from the platform to another
structure the following guidelines apply:
1. Where possible, place the platform over a roof or
walking structure to do the transfer.
2. Transfer your anchorage from one structure to the
other before stepping across.
3. Remember that you might be transferring to a struc-
ture where personal fall arrest is required.
4. Use the platform entrance, do not climb over or
through the guardrails.
Do not operate the aerial platform in windy or gusty condi-
tions. Do not add anything to the aerial platform that will
increase the wind loading such as billboards, banners,
flags, etc.
Never operate the aerial platform without all parts of the
guardrail system in place and the gate closed. Make
sure that all protective guards, cowlings, and doors are
securely fastened.
Do not exceed the platform capacity as indicated on the
platform rating placard on the platform. Do not carry loads
that extend beyond the platform guardrails without prior
written consent from Snorkel.
Do not operate the aerial platform from trucks, trailers, rail-
way cars, floating vessels, scaffolds, or similar equipment
unless the application is approved in writing by Snorkel.
Do not use the aerial platform as a crane, hoist, jack, or
for any purpose other than to position personnel, tools,
and materials.
Do not climb on the guardrails or use ladders, planks,
or other devices to extend or increase the work position
from the platform.
Take care to prevent rope, electrical cords, and hoses,
etc., from becoming caught in or on the aerial platform.
• If the platform or booms becomes caught on an adjacent
structure or other obstacle and is prevented from normal
motion, reverse the control to free the platform.
• If control reversal does not free the platform, evacuate
the platform before attempting to free it.
Hydraulic System
The hydraulic system contains hoses with hydraulic fluid
under pressure.
Danger
Hydraulic fluid escaping under pressure can have
enough force to inject fluid into the flesh. Serious
infection or reaction will result if medical treatment is
not given immediately. In case of injury by escaping
hydraulic fluid, seek medical attention at once.
Do not place your hand or any part of your body in front
of escaping hydraulic fluid. Use a piece of cardboard or
wood to search for hydraulic leaks.
Engine and Fuel Handling Precautions
Refer to the engine manufacturer’s Operator’s Manual for
complete information on safe engine operation, mainte-
nance, and specifications.
Danger
Engine exhaust contains carbon monoxide, a poi-
sonous gas that is invisible and odorless. Breathing
engine exhaust fumes will cause death or serious
illness. Do not run the engine in an enclosed area or
indoors without adequate ventilation.
Be careful not to run the diesel fuel tank empty. Bleed the
fuel system if air enters the lines between the tank and
the injection pump.
Allow the engine to return to idle before shutting the
engine off.
Do not smoke or permit open flames while fueling or near
fueling operations.
Never remove the fuel cap or fill the fuel tank while the
engine is running or hot. Never allow fuel to spill on hot
machine components.
Maintain control of the fuel filler nozzle when filling the
tank. Spilled fuel is a potential fire hazard.
Do not overfill the fuel tank. Allow room for expansion.