background image

 

 

20 

Safety Instructions & Operator’s Manual for 

 

TWO STAGE 
INTERMEDIATE FRAME 
SNOW THROWER 
SERIES 3 

 
 
 

IMPORTANT 

Snapper products are built using engines that meet or exceed all applicable emissions requirements on 
the date manufactured.  The labels on those engines contain very important emissions information and 
critical safety warnings.  Read, Understand, and Follow all warnings and instructions in this manual, the 
engine manual, and on the machine, engine and attachments.  If you have any questions about your 
Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at 
Snapper, McDonough, GA. 30253.  Phone: (1-800-935-2967). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

COPYRIGHT © 2000 
SNAPPER INC. 
ALL RIGHTS RESERVED 

 

INSTRUCTION No. 2-8543 (REV. 4, 3/30/00) 

 

 

        WARNING 

ENGINE EXHAUST, SOME OF ITS CONSTITUENTS, AND CERTAIN VEHICLE COMPONENTS CONTAIN OR 
EMIT CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER OR OTHER 
REPRODUCTIVE HARM. 

 

 

      WARNING 

BATTERY POSTS, TERMINALS AND RELATED ACCESSORIES CONTAIN LEAD AND LEAD COMPOUNDS, 
CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR OTHER 
REPRODUCTIVE HARM. WASH HANDS AFTER HANDLING. 

Summary of Contents for I55223





















Reviews: