background image

 

Safety Instructions & Operator’s Manual for 

EUROPEAN 

21” STEEL DECK 

WALK MOWERS 

SERIES 18 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

MODEL NUMBER EXPLANATION 

 

E

 

R  P  21 70 18  B  V 

 
EUROPEAN MODEL 

 

RECYCLING MODEL 

ENGINE DESIGNATION 

SELF-PROPELLED 

SERIES DESIGNATION 

CUTTING WIDTH 

ENGINE HORSE POWER * 

 

E – European Model 

R – Recycling Model 

 

18 - Series Designation 

B – Briggs & Stratton 

P – Self Propelled Model 

21 – 21” Cutting Width 

 

V – Overhead Valve 

 

70 – 7.0 HP (Engine Horse Power) 

 

 

 

 

 
 

Thank you for buying a SNAPPER Product!  Before operating your Walk Behind, read this manual carefully and pay 
particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 - 4. Remember that all power 
equipment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance 
with the operating instructions and common sense. 
 

NOTE: Specifications are correct at time of printing and are subject to change without notice.  
* Actual sustained equipment horsepower will likely be lower due to operating limitations and environmental factors.

 

 
 
 

 
COPYRIGHT © 2004 
SNAPPER – A DIVISION OF SIMPLICITY MFG., INC. 
ALL RIGHTS RESERVED 

MANUAL No. 2-9767 (I.R. 8/9/04)

 

MODELS 

EP217018BV 

ERP217018BV 

 

Summary of Contents for EP217018BV





























Reviews: