background image

Safety Instructions & Operator's Manual for

NOTE: Specifications are correct at time of printing and are subject to change without notice.
* Actual sustained engine power will likely be lower due to operating limitations and environmental factors.

COPYRIGHT © 2006
SNAPPER - A DIVISION OF SIMPLICITY MFG., INC.
ALL RIGHTS RESERVED

MANUAL No. 7100981 (I.R. 10/30/2006)

TP 100-5211-IR-WB-N

SELF-PROPELLED

MODEL

ELP216753BDV

MODEL DESIGNATION

ENGINE OPTIONS

SELF-PROPELLED

SERIES DESIGNATION

CUTTING WIDTH

ENGINE POWER *

Thank you for buying a SNAPPER Product!  Before operating your Walk Behind, read this manual carefully and pay
particular attention to the “IMPORTANT SAFETY INSTRUCTIONS” on Pages 2 - 4. Remember that all power equip-
ment can be dangerous if used improperly. Also keep in mind that SAFETY requires careful use in accordance with
the operating instructions and common sense!

MODEL NUMBER EXPLANATION 

EUROPEAN

21” CAST ALUMINUM DECK

WALK MOWERS

SERIES 3

E – European Model

P – Self Propelled 

675 – 6.75 (Engine Power)

B – Briggs & Stratton

L – Aluminum Deck 

21 – 21” Cutting Width

3 - Series Designation

DV – DOV™ Engine

E

L

P

21

675

3

BDV

Summary of Contents for ELP216753BDV





















Reviews: