background image

1

Snap-on EEBC300A
Fleet Battery Charger
User's Manual  

IMPORTANT SAFETY INSTRUCTIONS

This manual contains important safety and operating
instructions for 

Snap-on Fleet Battery Charger model

EEBC300A. Refer to the information in this manual often for
safe operation.

Read All Instructions

Read, understand and follow all safety messages and
instructions in this manual and on the test equipment. Safety
messages in this section of the manual contain a signal word, a
three-part message, and, in some instances, an icon.

The signal word indicates the level of hazard in a situation:
• Danger indicates an imminently hazardous situation which, if

not avoided, will result in death or serious injury to the
operator or bystanders.

• Warning indicates a potentially hazardous situation which, if

not avoided, could result in death or serious injury to the
operator or bystanders.

• Caution indicates a potentially hazardous situation which, if

not avoided, may result in moderate or minor injury to the
operator or bystanders.

The three-part message uses three different type styles to
further define the potential hazard.
• Normal type states the hazard.
• Bold type states how to avoid the hazard.

Italic type states the possible consequences of not avoiding
the hazard.

An icon, when present, gives a graphical description of the
potential hazard.

SAVE THESE  INSTRUCTIONS

Summary of Contents for EEBC300A

















Reviews: