Smeg SR964NGH Manual Download Page 1

25

Contents

THESE INSTRUCTIONS ARE VALID ONLY FOR THE DESTINATION COUNTRIES
WHOSE IDENTIFYING SYMBOLS ARE INCLUDED ON THE COVER OF THIS
MANUAL.

INSTRUCTIONS FOR THE USER: these contain user advice, the description
of the controls and the correct procedures for cleaning and maintenance of
the appliance.

INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified
technician who must install the appliance, set it functioning and carry out
an inspection test.

1. INSTRUCTIONS FOR USE..................................................... 26
2. SAFETY PRECAUTIONS........................................................ 28
3. ENVIRONMENTAL RESPONSIBILITY ................................... 30
4. USING THE HOB .................................................................... 31
5. CLEANING AND MAINTENANCE .......................................... 33
6. POSITIONING IN THE COUNTER TOP ................................. 36
7. ELECTRICAL CONNECTION ................................................. 38
8. GAS CONNECTION ................................................................ 39
9. ADAPTATION TO DIFFERENT TYPES OF GAS ................... 41

Summary of Contents for SR964NGH























Reviews: