background image

Contents 

 

 

23 

 
 

1

 

INSTRUCTIONS FOR SAFE AND PROPER USE ____________________ 24

 

2

 

POSITIONING OF THE HOB ____________________________________ 26

 

3

 

ELECTRICAL CONNECTION ____________________________________ 28

 

4

 

GAS CONNECTION ___________________________________________ 29

 

5

 

ADAPTATION TO DIFFERENT TYPES OF GAS _____________________ 31

 

6

 

FINAL OPERATIONS __________________________________________ 35

 

7

 

USING THE HOB______________________________________________ 38

 

8

 

CLEANING AND MAINTENANCE_________________________________ 41

 

 

 
 
 
 
 
 
 
 
 
 

THESE INSTRUCTIONS ARE VALID ONLY FOR END USER COUNTRIES 

WHOSE IDENTIFICATION SYMBOLS APPEAR ON THE COVER OF THIS 
MANUAL. 

 
 

 

 

INSTRUCTIONS FOR THE INSTALLER: these are for the 

qualified 

technician 

who must carry out a suitable check of the gas system, 

install the appliance, set it functioning and carry out an inspection test. 

 

   

 

 

INSTRUCTIONS FOR THE USER: these contain user advice, 

description of the commands and the correct procedures for cleaning 

and maintenance of the appliance. 

 

Summary of Contents for SER64XGNL





















Reviews: