background image

Contents 

 

 

 

 

1.

 

Precautions for safety and use_________________________ 4

 

2.

 

Instructions for disposal – our enviromental care___________ 5

 

3.

 

Safety instructions __________________________________ 6

 

4.

 

Fitting the appliance in the top _________________________ 7

 

4.1

 

Fixing to the supporting structure ________________________________________7

 

4.2

 

Fitting the adhesive foam rubber strip_____________________________________8

 

4.3

 

Fitting the fixing clips _________________________________________________8

 

4.4

 

Fitting the hob into the hole in the work-top ________________________________8

 

5.

 

Electrical connection ________________________________ 9

 

5.1

 

Clearances above and around domestic appliances ________________________10

 

6.

 

Gas connection ___________________________________ 12

 

6.1

 

Connection to liquid gas ______________________________________________12

 

6.2

 

Room ventilation ____________________________________________________12

 

6.3

 

Combustion gas discharge ____________________________________________12

 

7.

 

Adapting to different types of gas______________________ 13

 

7.1

 

Removing the hob skin _______________________________________________13

 

7.2

 

Burner and nozzle characteristics table __________________________________14

 

7.3

 

Hob burner layout ___________________________________________________14

 

7.4

 

Adjusting the primary air flow __________________________________________14

 

7.5

 

Reassembling the hob skin____________________________________________15

 

7.6

 

Adjusting the minimum setting for natural gas _____________________________15

 

7.7

 

Adjusting the minimum setting for liquid gas_______________________________15

 

7.8

 

Greasing the gas taps________________________________________________15

 

8.

 

Description of controls ______________________________ 16

 

8.1

 

The front panel _____________________________________________________16

 

9.

 

Using the hob _____________________________________ 17

 

9.1

 

Fitting the pan stands ________________________________________________17

 

9.2

 

Lighting burners with safety device______________________________________20

 

9.3

 

Practical hints for using the burners _____________________________________20

 

9.4

 

Pan diameters______________________________________________________20

 

10.

 

Cleaning and maintenance_________________________ 21

 

10.1

 

Cleaning the hob____________________________________________________21

 

10.2

 

Cleaning instructions for an acid-etched glass hob _________________________21

 

10.3

 

Cleaning the components _____________________________________________21

 

 
 

 

Thank you for choosing our product. 

We advise you to read this manual carefully. It contains all necessary instructions for 
maintaining unaltered the appearance and functional qualities of the cooking hob. 

 

 

INSTRUCTIONS FOR THE INSTALLER:

 these are intended for the 

authorized 

person

 who is to check the gas supply system and install, commission and test the 

appliance. 

 

 

INSTRUCTIONS FOR THE USER:

 these provide recommendations for use, a 

description of the controls and the correct procedures for cleaning and maintaining the 
appliance. 

Summary of Contents for PVA750A





















Reviews: