background image

10  -  USE

91477A688/A

appliances and do not remove plugs from 
power sockets. Do not use phones or 
mobile phones inside the building.

• Open the window in order to ventilate the 

room.

• Call customer assistance services or your 

gas supplier.

Malfunctions

Any of the following indicate a malfunction and 
you should contact a service centre.
• The burners do not ignite properly.
• It is difficult to keep the burners lit.
• The burners go out when the appliance is in 

use.

• It is difficult to turn the gas cocks.

Preliminary operations

• Remove any protective film from the outside 

or inside of the appliance, including 
accessories.

• Remove any labels (apart from the technical 

data plate) from the accessories and 
shelves.

• Remove and wash all the appliance 

accessories (see “CLEANING AND 
MAINTENANCE”).

Practical tips for using the hob

For better burner efficiency and to minimise gas 
consumption, use pans with lids and of suitable 
size for the burner, so that the flames do not 
reach up the sides of the pan. Once the contents 
come to the boil, turn down the flame far 
enough to ensure that the liquid does not boil 
over.

Using the accessories

Raised pan support

The raised pan supports should be placed on 
the hob pan supports. Make sure they are 

placed properly. 

Using the hob

All the appliance’s control and monitoring 
devices are located together on the front panel. 
The burner controlled by each knob is shown 
next to the knob. The appliance is equipped 
with an electronic ignition device. Simply press 
the knob and turn it anti-clockwise to the 
maximum flame symbol, until the burner ignites. If 
the burner does not light in the first 15 seconds, 
turn the knob to 

 and wait 60 seconds 

before trying again. After lighting, keep the knob 
pressed in for a few seconds to allow the 
thermocouple to heat up. The burner may go out 
when the knob is released: In this case, the 
thermocouple has not heated up sufficiently.
Wait a few moments and repeat the operation. 
Keep the knob pressed in longer.

Usable cookware diameters

Pan diameters that can be used with the 
raised pan support

See General safety instructions.

In case of an accidental switching off, a 
safety device will be tripped, cutting off 
the gas supply, even if the gas cock is 
open. Return the knob to 

 and wait 

at least 60 seconds before lighting it 
again.

Burner

Pan diameter

UR2

24 - 28

R

18 - 24

AUX

12 - 16

Burner

Pan diameter (cm)

UR2

 28 - 32 

R

26 - 28

AUX

-

Summary of Contents for PGA32G


















Reviews: