background image

25

Contents

THESE INSTRUCTIONS ARE VALID ONLY FOR THE DESTINATION COUNTRIES
WHOSE IDENTIFYING SYMBOLS ARE INCLUDED ON THE COVER OF THIS
MANUAL. THIS IS A CLASS 3 BUILT-IN HOB.

INSTRUCTIONS FOR THE USER: these instructions contain user
recommendations, a description of the controls and the correct
procedures for cleaning and maintenance of the appliance.

INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified
technician who must install the appliance, set it functioning and carry out
an inspection test.

1.

INSTRUCTIONS FOR USE ......................................................................... 26

2.

SAFETY PRECAUTIONS ............................................................................ 28

3.

ENVIRONMENTAL RESPONSIBILITY........................................................ 30

4.

DESCRIPTION OF CONTROLS.................................................................. 31

5.

USING THE HOB......................................................................................... 32

6.

CLEANING AND MAINTENANCE ............................................................... 35

7.

POSITIONING ON THE HOB TOP.............................................................. 37

8.

ELECTRICAL CONNECTION...................................................................... 39

9.

GAS CONNECTION .................................................................................... 40

10.  ADAPTATION TO DIFFERENT TYPES OF GAS....................................... 42

Summary of Contents for P755AB























Reviews: