SMC Networks ZK2 A Series Page 42 Operation Manual Download

Page: 42 / 80

-41-

No. ZK2-OM01301

7.4. Replacement Parts

No.

Item

Remarks

Tension bolt assembly

2 pcs. per set

Port plug assembly

Plug for changing PV port to single side supply type

(Common for mm and inch type)

Port plug assembly

Plug for changing PS or PD port to single side supply type

(Common for mm and inch type)

One-touch fitting assembly

Metric size: ø8, Inch size: ø5/16

”

Sound absorbing material

2 pcs. per set - Material: Non-woven cloth

(Silencer cover is not included.)

DIN rail mounting bracket

1 piece for U side and D side

DIN rail

Refer to Dimensions in the Catalog for the recommended length for each

number of manifolds stations.

Connector housing

assembly

Available connector is even number only. (If you need a connector for odd

number, specify the connector of the number you need +1 station.)

Note) When ordering a manifold

“ZZK2□A-□□□-□-A” on

page 12

, 1 to 3 are delivered as a set.

7.5. Replacement Parts for Manifold/How to Order

(3) Tension bolt assembly

(2 pcs. per set)

ZK2-TB1- 05 -A

(4) Port plug assembly (5) Port plug assembly

(Purchasing order is available in units of 1 piece.) (Purchasing order is available in units of 1 piece.)

VVQZ2000-CP ZK2-MP1C6-A

Applicable stations

For 1 station manifold

…

For 10 stations manifold

Summary of Contents for ZK2 A Series

















































































Search results

Summary of Contents for ZK2 A Series

Reviews:

Related manuals for ZK2 A Series

Brands by name

Popular brands

SMC Networks ZK2 A Series, Operation Manual

Search results

Summary of Contents for ZK2 A Series

Reviews:

Related manuals for ZK2 A Series

Brands by name

Popular brands