VCHR30-TFR04
Page 2of 2
4 Settings
•
The outlet pressure is set by rotating the adjusting bolt, at the bottom of
the regulator. SeeFigure 3.Loosen the locknut first.
•
The adjusting bolt (32 mm across flats) can be rotated by a spanner,
or with a screwdriver using the Ø11mm hole in the bolt head.
Warning
•
Adjust the outlet pressure while confirming the pressure gauge values on
the inlet and outlet sides.
•
Over-rotating the adjusting bolt will damage the inner components of the
product.
•
The set outlet pressure should be less than 85% of the inlet pressure.
•
Setting the outlet pressure to more than 85% of the inlet pressure may
cause fluctuation of flow or pressure on the inlet side, resulting in
unstable operation.
•
The maximum value of the set pressure range has a tolerance,
therefore, the set pressure may exceed this value.
•
Tighten the locknut when adjustment is complete. The locknut is not
an anti-tamper device. Appropriate measures against foreseeable
misuse must be taken if this can cause a hazard.
Caution
•
Adjust after carefully confirming the inlet pressure.
•
When adjusting the outlet pressure, a torque is applied to the adjusting
bolt. Support the product separately, so that the torque force is not
transferred to the external piping.
Reference for Adjusting bolt Torque
Set pressure
1 MPa
2 MPa
3 MPa
4 MPa
5 MPa
Torque N
·
m
3
6
9
12
15
Table 2
•
Setting the outlet pressure should be conducted by increasing the
pressure.
•
Setting the outlet pressure by decreasing the pressure may result in
going below the required set pressure.
•
Turning the adjusting bolt in the clockwise direction, increases the
pressure.
•
Turning the adjusting bolt counter-clockwise, will decrease the outlet
pressure.
5 How to Order
6 Outline Dimensions (mm)
Figure 5
7 Maintenance
7.1 General Maintenance
•
This product does not require maintenance. However the following
advice should be followed:
Ensure the proper function of the regulator is regularly
checked
Ensure there is no build-up of dirt or debris on the regulator,
especially around the vent ports and adjustment screw.
Caution
•
Not following proper maintenance procedures could cause the product to
malfunction and lead to equipment damage.
•
If handled improperly, compressed air can be dangerous. Maintenance
of pneumatic systems should be performed only by qualified personnel.
•
Before performing maintenance, turn off the power supply and be sure to
cut off the supply pressure. Confirm that the air is released to
atmosphere.
•
After installation and maintenance, apply operating pressure and power
to the equipment and perform appropriate functional and leakage tests
to make sure the equipment is installed correctly.
•
Do not make any modification to the product.
•
Do not disassemble the product, unless required by installation or
maintenance instructions.
8 Limitations of Use
Warning
•
This product must not be used as a safety accessory as defined by the
Pressure Equipment Directive 97/23/EC.
•
Install a protective device if the outlet pressure exceeding the set outlet
pressure could cause equipment damage or malfunction.
•
The outlet pressure may fluctuate when the air has not been consumed
for a long time, or the product is used in a shut-off or balancing circuit on
the outlet side.
•
Grease may leak into the outlet side, as it is applied to inner sliding parts
and seals.
•
Do not use in circuits requiring highly precise relief sensitivity or setting
precision.
9 Contacts
AUSTRIA
(43) 2262 62280-0
LATVIA
(371) 781 77 00
BELGIUM
(32) 3 355 1464
LITHUANIA
(370) 5 264 8126
BULGARIA
(359) 2 974 4492
NETHERLANDS
(31) 20 531 8888
CZECH REP.
(420) 541 424 611
NORWAY
(47) 67 12 90 20
DENMARK
(45) 7025 2900
POLAND
(48) 22 211 9600
ESTONIA
(372) 651 0370
PORTUGAL
(351) 21 471 1880
FINLAND
(358) 207 513513
ROMANIA
(40) 21 320 5111
FRANCE
(33) 1 6476 1000
SLOVAKIA
(421) 2 444 56725
GERMANY
(49) 6103 4020
SLOVENIA
(386) 73 885 412
GREECE
(30) 210 271 7265
SPAIN
(34) 945 184 100
HUNGARY
(36) 23 511 390
SWEDEN
(46) 8 603 1200
IRELAND
(353) 1 403 9000
SWITZERLAND
(41) 52 396 3131
ITALY
(39) 02 92711
UNITED KINGDOM
(44) 1908 563888
URL :
http// www.smcworld.com (Global) http// www.smceu.com (Europe)
Specifications are subject to change without prior notice from the manufacturer.
©
2013
SMC Corporation All Rights Reserved.
