SMC Networks SY 5000 Series: SY7000 Series, Operation Manual

Page: 28 / 36

SY3000*-OMJ0003-A
-27-
Style of manifold Manifold block assembly part no. Note
For 45(N)F
(D-sub connector)
SX
3
5
000-50-3A-□□
For 45(N)
(Flat ribbon cable)
For 45 G
PC Wiring System compatible
SX
3
5
000-50-5A-□□
For 45
(Terminal block)
SX
3
5
000-50-7A-□□
□□
：
A,B port SY3000(metric size) C4:With one-touch fitting for
φ
4
C6:With one-touch fitting for
φ
6
(inch size) N3:With one-touch fitting for
φ
5/32”
N7:With one-touch fitting for
φ
1/4”
A,B port SY5000(metric size )C4:With one-touch fitting for
φ
4
C6:With one-touch fitting for
φ
6
C8:With one-touch fitting for
φ
8
(inch size) N3:With one-touch fitting for
φ
5/32”
N7:With one-touch fitting for
φ
1/4”
N9:With one-touch fitting for
φ
5/16”
ＳＹ
ＳＹ ＳＹ
ＳＹ Ｓｅｒｉｅｓ
Ｓｅｒｉｅｓ Ｓｅｒｉｅｓ
Ｓｅｒｉｅｓ
ＳＹ
ＳＹ ＳＹ
ＳＹ３０００
３０００ ３０００
３０００・
・ ・
・５０００
５０００ ５０００
５０００・
・ ・
・７０００
７０００ ７０００
７０００ Ｓｅｒ
Ｓｅｒ Ｓｅｒ
Ｓｅｒｉｅｓ
ｉｅｓ ｉｅｓ
ｉｅｓ
Specific Product Precautions 20
Be sure to read before handing.
DIN Rail Manifold Exploded View
How to Increase Manifold Bases
Station expansion is possible at any position.
□
1 Loosen bolt○
a
fixing the manifold base until it begins to turn
idly.(While pressing DIN rail releasing buttons○
c
, at two
locations, separate the manifold base from the DIN rail.)
□
2 Additional bases are to be added to the U side. Press
splitting button ○
b
of the manifold block assembly on the U
side until button ○
b
locks and then separate the block
assemblies.
□
3
Separate the connector block assembly in the same manner
as
□
2
, and remove the connector mounting screw shown
in Fig. 1
□
4 Loosen the valve mounting screw on the U side, remove the
valve, and take out the receptacle housing.(Refer to Fig.
2.)
□
5 Insert the common wire (red) of the manifold block
assembly to be added into the pin insertion section(N mark)
of the receptacle housing that was taken out in
□
4 , mount it
on the manifold block, and mount the removed valve.
□ 6
As shown in Fig. 3, mount the additional manifold block
assembly on the DIN rail on the U side. Refer to the circuit
diagram, and insert the lead wire (black) as shown in Fig.
4.
□
7 Press the blocks against each other until a click sound is
produced, place the lead wire in the manifold block, and
close the lid without pinching the lead wire.
□
8 While lightly holding the blocks together so that there are no
gaps between them, secure them to the DIN rail by
tightening the DIN rail holding screws○
a
. (Tightening torque:
1.4Nm)
Note 1) Depending on the connector, there is a limit to the number of
solenoids that can be used. Manifold bases that can be added
cannot exceed the number of usable solenoids.
Note 2) The manifold block assembly mounting position for additional
manifold bases is always on the U side,because wires are
connected to repective connectors sequentially from the D side.
Note 3) When
bolt○
a
for the end bolck is not sufficiently tightened during
reassembly, air leakage may result.
Before supplying air, check that there is no gap between blocks
and that the manifold block is firmly fixed to the DIN rail in order
to ensure air supply without leakage.
Caution