Base hole dimension
Base hole dimension
w
Base hole dimension
q
7.4
38.1
(Lead wire AWG#26)
300
±
5
5
10.3
8.4
(7.4)
4.5
5
(Lead wire AWG#26)
≈
300
54
11.6
(11.6)
4
4
4
4
10
4 4
4.9
10
3.4
9.8
0.3
2.6
2.2
2 x ø2.8
4.5
±
0.05
10
2 x M2 x 0.4
Thread depth: 6 or more
2 x ø3
(Port hole dimension)
(4.5
±
0.05
)
(2 x ø3 )
2.2
C0.2 or less
3.4
Mounting screw (Included)
M2 x 11
3
1.7
1.7
ø3
ø3
1.7
ø3
2.45
0.8
2.3
1.5
1.7
1.7
0.8
2.45
1.5
2.3
1.7
ø3
ø3
ø3
2 x M2 x 0.4
Thread depth: 6 or more
Tightening torque: 0.1 to 0.14 N·m
2.1
2 x M2 x 0.4
Thread depth: 6 or more
Tightening torque: 0.1 to 0.14 N·m
+0.05
0
+0.05
0
Mounting screw (Included)
M2 x 11
1 (SUP) port
1(P) port
2(A) port
8.3
8.9
10
10
9.8
10
2 (OUT) port
3 (EXH) port
2 (OUT)
1 (IN)
Normally closed
Universal
Universal
2
(OUT)
1
(SUP)
3
(EXH)
2 (OUT)
1 (IN)
Dimensions
2-port
SX91
/Normally closed
SX92
/Universal
3-port
SX090
/Universal
1. For the solenoid valve without power-saving circuit, continuous energization is not
allowed at the start-up voltage (rated voltage) as there is a risk of damaging the coil.
For continuous energization with the holding voltage, please make sure
the coil surface temperature does not exceed 80
°
C.
2. Coil temperature may get high due to ambient temperature or
energizing duration. Do not touch the valve by hand directly.
When there is such a dangerous case to be touched by hands directly, install a protective cover.
3. When using the solenoid valves on a manifold, note that the temperature rise will be
larger if three or more adjacent valves are energized together. Please ensure that the
coil surface temperature does not exceed 80
°
C in the actual operating conditions.
1. To operate the manual override to the ON position, press the button
fully in the direction of the arrow (approximately 0.5 mm). The valve
will be turned OFF when the button is released.
(For 3-port valve)
Continuous Energization
Manual Override
Specific Product Precautions
Be sure to read this before handling the products.
Refer to the back cover for safety instructions.
Caution
Caution
1. Confirm that the gasket is correctly mounted on the body interface
and then tighten the screws to the specified torque.
(Fasten equally so that the valve will not tilt.)
The specified torque is from 0.10 to 0.14 N·m, please apply a torque
setting depending on the base condition and operating environment.
2. Please do not apply force to the coil and frame when installing the
piping and valves.
If they receive 10 N or more of force, a malfunction may occur.
3. Do not pull the lead wire with excessive force.
Applying 10 N or more of load may result in broken wire or contact
failure.
Valve Mounting
Caution
ø3 push part
-9-
