manualshive.com logo in svg

SMC Networks ProtoCessor FPC-ED2, Startup Manual

Share
Download
SMC Networks ProtoCessor FPC-ED2 Startup Manual Download Page 36

Additional Information 

 
 
 

 

VorTek ProtoCessor Start-up Guide 

36 

 
 

9.4

 

LED Diagnostics for Communications Between  ProtoCessor and Devices  

See the diagram below for ProtoCessor FPC-ED2 LED Locations. 

 

Tag 

Description 

Run 

The Run LED will start flashing 20 seconds after power indicating normal operation. The 

Heat 

Beat 

LED has the same functionality but flashes more rapidly. 

Sys/ 

Config 

Error 

The Sys/Config Error LED will go on solid 15 seconds after power up. It will turn off after 5 
seconds. A steady red light will indicate there is a system error on ProtoCessor. If this occurs, 
immediately report the related “system error” shown in the error screen of the FS-GUI 
interface to support for evaluation. 

Node Offline 

The Node Offline LED will turn on and stay solid if there is no communication with the device. 

RX 

The RX LED will flash when a message is received on the field port. 

TX 

The TX LED will flash when a message is sent on the field port. 

PWR 

The power light should show steady green when connected to a functioning power source. 

Figure 38: Diagnostic LEDs 

 

Summary of Contents for ProtoCessor FPC-ED2


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands