manualshive.com logo in svg

SMC Networks PFG3 0 Series, Operation Manual

Share
Download
SMC Networks PFG3 0 Series Operation Manual Download Page 44

 

-43- 

 

No.PF

※※

-OMU0007-B 

 

 

■

[F 3] Digital filter setting 

The digital filter can be selected to filter the flow measurement (0 to 30 sec.). 
Output chattering or display flicker in measurement mode can be reduced by setting the digital filter. 

 

<Operation> 

Press the 

  or 

  button in function selection mode to display [F 3]. 

Press the 

  button. 

  Move on to digital filter setting. 

 

Digital filter setting 

Press the 

  or 

  button to select the digital filter. 

Digital filter set range: 0.00 to 30.00 [S] 

 

 

Press the 

  button to set. 

  Return to function selection mode. 

 

[F 3] Digital filter setting completed 

 
 

1: Each set value is a guideline for 90% response time. 

2: The Switch output and flow display/analogue output are affected. 

When only the switch output needs to be filtered, select and adjust the delay time setting. (page 

36

 and 

41

) 

Summary of Contents for PFG3 0 Series






















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands